PDA

View Full Version : Yasaka Mark V for Donic Persson Exclusive OFF



Revenna
06-30-2018, 05:17 AM
Thinking of this combo. Donic Persson Exclusive OFF with Yasaka Mark V. Not sure if it is good.

trumpet_guy
06-30-2018, 05:38 AM
Revenna, this should be a good setup. I enjoy using Mark V. The Blade appears to be a good match for it.

Floris
06-30-2018, 12:06 PM
Mark-V is surprisingly good with polyball.

KM1976
06-30-2018, 12:59 PM
I completely agree with Floris here. If you are looking for a controlled do it all rubber then don't think any further. Mark V is really good with polyball.

NeatRiver
07-03-2018, 11:15 AM
Thinking of this combo. Donic Persson Exclusive OFF with Yasaka Mark V. Not sure if it is good.

I don't know what your level of play is, But this combination feels very slow / dead. About a year ago I played with Donic Person exclusive off with 2.0 Baracuda on FH and Mark V HPS soft on the BH and that combination took my game to a different level. It was good in doing every thing, Loops, push, block. Until I changed my blade to a bit faster / harder blade Tibhar Stratus power wood with 2.0 baracuda on both sides and which I really enjoy now. I wanted to get a bit slower setup for my brother and got him Tibhar Stratus Power wood with Mark V 2.0 on both sides and what a dead setup that is. And for that reason I think with even a slower / softer blade like Donic person EO and Mark V it will be quite slow / dead. Hope this helps.

Cobalt765
07-03-2018, 11:49 AM
I've only used Mark V once. On a Stiga Allround Classic WRB and the combo was awful. Dead. I struggle to get the ball over the net. Having said that, it can't be a highly popular classic rubber for no reason.

laistrogian
07-03-2018, 12:36 PM
I really dont recommend mark v.

I would recommend getting xiom vega europe instead

kenshiro
07-03-2018, 01:01 PM
if the classic mark v feels slow and king of dead you should try the mark v hps , its the same rubber but with a much faster sponge, works good with the new balls.

sderyke2002
07-03-2018, 01:41 PM
I play a lot with Mk V on at least one side of my many blades (usually the backhand for the added control). Yes it is slower than one of the Rakza's I usually have on the other side but that does not represent much of a problem if your loop is spinney enough. I find it pushes more predictably and is less susceptible to incoming spin than the newer rubbers. Remember MkV has a hard sponge so it doesn't provide the needed speed until you drive it hard with the proper technique. Is slowness comes from the soft rubber which is where it gets its spin. So whether this fits for you or not depends mainly on your style and form.

I also have a Sweden Classic (which is a pretty slow blade) that I purposely put MkV HPS on one side and Valmo on the other to see how faster rubbers would work with a slower blade. They are both much faster than MkV original and with the slow bat function well, very similar to my carbon bats with the Mk V on the backhand, so you might want to consider one or the other if the MkV you try feels too slow on that All Around bat you are holding on to.

Having tried both approaches (slow bat/fast rubber VS fast bat slow rubber) I would go with fast bat and slow rubber, like a Ma Lin EO and Mk V (which you can get for under $100). But my style is fast close the table and I myself am moving towards even more speed (more fast bat/fast rubber) and that may not be what you want at all.

Also Yasaka has released a new rubber called Rigan, which is meant to bridge the gap between classical rubbers and the modern sponge. I haven't tried it because I can't find anyone selling it yet, but it may be worth a look as a fast replacement for MkV.