Search:

Type: Posts; User: Lazer; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. No you obviously do not understand, it depends on...

    No you obviously do not understand, it depends on the top layer a soft layer like hinoki breaks much easier than a hard one like walnut. But any wood may break. The longer you wait to change the...
    Replies
    38
    Views
    961
  2. I care not to get the top layer destroyed when...

    I care not to get the top layer destroyed when changing rubbers. maybe You dont...
    Replies
    38
    Views
    961
  3. The question here was wether this was glue or...

    The question here was wether this was glue or lacquer,
    Replies
    38
    Views
    961
  4. Impossible, speed and control are each other’s...

    Impossible, speed and control are each other’s inverse. High speed low control and high control low speed.

    Cheers
    L-zr
    Replies
    7
    Views
    341
  5. The surface is too even, if it’s glue it should...

    The surface is too even, if it’s glue it should be more wavy…

    Cheers
    L-zr
    Replies
    38
    Views
    961
  6. Sounds like a bad glue job… Of the blade itself…...

    Sounds like a bad glue job…
    Of the blade itself…

    Cheers
    L-zr
    Replies
    38
    Views
    961
  7. Have you ever seen varnish on a voided boat? It...

    Have you ever seen varnish on a voided boat?
    It depends entirely on how it’s done and with what type of lawyer. I use a thin layer of good old fashioned varnish. It looks pretty much the same as the...
    Replies
    38
    Views
    961
  8. No can’t be it too glossy…

    No can’t be it too glossy…
    Replies
    38
    Views
    961
  9. That’s funny because a thick layer of glue is far...

    That’s funny because a thick layer of glue is far worse in that sense compared to a thin layer of lacquer…

    Cheers
    L-zr
    Replies
    38
    Views
    961
  10. 1. It protests the blade from the water in modern...

    1. It protests the blade from the water in modern glue.
    2. It prevents the top layer to rip when changing rubbers.

    I always always always use a small layer of lacquer.
    I also remove the rubber...
    Replies
    38
    Views
    961
  11. I love Nittaku premium I think they and DHS DJ...

    I love Nittaku premium I think they and DHS DJ 40+ are the absolute best, both have seams. You don’t really need to feed your robot with that quality. It’s better to change the robot rather than have...
    Replies
    38
    Views
    911
  12. Didn’t know about the process, thanks for the...

    Didn’t know about the process, thanks for the info.

    CheersL-zr
    Replies
    38
    Views
    911
  13. No the top sheet can make a lot of difference....

    No the top sheet can make a lot of difference. Yes the leftover method will work.
    But seriously you will need an instrument to do it properly. And also all the stated hardness is approximate, it can...
  14. It shouldn’t have to be like this, it must have...

    It shouldn’t have to be like this, it must have something to do with old casting forms or whatever and new material. But this is the way it is.

    Cheers
    L-zr
    Replies
    38
    Views
    911
  15. No it has not the + means that diameter is...

    No it has not the + means that diameter is slightly bigger by a tiny fraction.

    Cheers
    L-zr
    Replies
    38
    Views
    911
  16. The hardness is in regards to the sponge only, so...

    The hardness is in regards to the sponge only, so if you want to tests thoroughly you should do it without top sheet….

    Cheers
    L-zr
  17. Against a defender like this You will need to...

    Against a defender like this You will need to hard. To try to hit soft is almost suicide, The harder You hit the less effect the incoming spin will have...

    Cheers
    L-zr
    Replies
    13
    Views
    832
  18. It should, soft rubbers generally have bigger air...

    It should, soft rubbers generally have bigger air (or whatever their filled with) pockets than hard rubbers.
    Here is a page with data that people have submitted: Rubber Sheet Mass and Size Database...
  19. I can use this system, we call it bank ID, The...

    I can use this system, we call it bank ID, The problem is probably your bank. At least here the bank handles the identification. I used this with tt11.

    Cheers
    L-zr
  20. I’ll get that too, but I find my posts are...

    I’ll get that too, but I find my posts are registered so I don’t try to repost, something is wrong with this board. Maybe it needs braking in…
    Replies
    102
    Views
    3,048
  21. It’s slower than an average ESN rubber but faster...

    It’s slower than an average ESN rubber but faster than regular MarkV. I get a little less spin on hard shots but I hit the table almost all the time.,, It last just as long as an ESN rubber. I...
  22. You could try Mark V HPS. It has the same top...

    You could try Mark V HPS. It has the same top sheet but a little more modern sponge. I love on my 5 ply all wood blade. The speed decided by the composition and with hard wood an all wood blade can...
  23. You guys must have gotten some kind of hickups. ...

    You guys must have gotten some kind of hickups.
    hick, hick😗

    Cheers
    L-zr
    Replies
    102
    Views
    3,048
  24. If you switch to a heavier rubber the balance...

    If you switch to a heavier rubber the balance moves upwards and if you switch to a lighter rubber the balance moves downwards.
    Replies
    12
    Views
    632
  25. The balance does a lot too. It’s very...

    The balance does a lot too.
    It’s very individual. My preference:
    Middle < balance > high, (by SDC) or a little towards head heavy,
    180g < weight > 190g

    Cheers
    L-zr
    Replies
    12
    Views
    632
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Create a new Topic:
Title is required.