Back to Forum
Results 1 to 10 of 10
  1. Richie is offline
    This user has no status.
     
    Advanced TTD Member 604 328
    R
    Richie is offline
    This user has no status.
     
    Advanced TTD Member 328 604

    User Info Menu

    #1

    Removing residue glue from blade?

    Does anyone know of a trick to remove tiny bits of residue glue from blades? I borrowed some glue a while ago that was really thin and it has been hell to remove. I've scrubbed for ages and got most of it out from the middle, but there is still like a very thin layer and residual glue everywhere, mostly on the edges.

    Is there some kind of solution I could pour on the blade that will remove the glue without damaging it?

    Thanks all.

    It's hard to see even in the picture.

    The Following User Likes Richie's Post:

    Equaaz


  2. PingBirdPong is offline
    says Verified Cheater, Banned by ITTF :)
     
    Advanced TTD Member 142 252
    PingBirdPong's Avatar
    PingBirdPong is offline
    says Verified Cheater, Banned by ITTF :)
     
    Advanced TTD Member 252 142
    #2
    Quote Originally Posted by Richie
    Does anyone know of a trick to remove tiny bits of residue glue from blades? I borrowed some glue a while ago that was really thin and it has been hell to remove. I've scrubbed for ages and got most of it out from the middle, but there is still like a very thin layer and residual glue everywhere, mostly on the edges.

    Is there some kind of solution I could pour on the blade that will remove the glue without damaging it?

    Thanks all.

    It's hard to see even in the picture.

    You can apply a few layers of glue to just the blade, when it has a thick enough layer, it’s peel it all off. If it’s just little bits, scrub it off with a rubber cleaning sponge

    The Following User Likes PingBirdPong's Post:

    Richie

    Modestly, Leo

  3. Zwill is offline
    This user has no status.
     
    Established TTD Member 65 137
    Zwill's Avatar
    Zwill is offline
    This user has no status.
     
    Established TTD Member 137 65

    User Info Menu


    Oct 2018
    Hungary
    137
    65
    70
    Read 0 Reviews
    #3
    The best trick is to keep the edge of the rubbers you cut off and use those to clean the blades.

  4. brokenball is offline
    This user has no status.
     
    Elite TTD Member 468 1,006
    B
    brokenball is offline
    This user has no status.
     
    Elite TTD Member 1,006 468

    User Info Menu

    #4
    I have just used the palm of my hand to rubber the blade. The glue warms up and will start to roll in little clumps. Heating the blade with a hair dryer will warm up the rubber faster and save some skin.

    The Following 3 Users Like brokenball's Post:

    lodro, Richie and 1 other


  5. lodro is offline
    says TT-CLOWN, old git
     
    Senior TTD Member 281 796
    L
    lodro is offline
    says TT-CLOWN, old git
     
    Senior TTD Member 796 281
    #5
    Quote Originally Posted by brokenball
    I have just used the palm of my hand to rubber the blade. The glue warms up and will start to roll in little clumps. Heating the blade with a hair dryer will warm up the rubber faster and save some skin.

    WARNING ! Heating a blade with a hair dryer can lead to bending and warping . !!!!!!!


  6. Richie is offline
    This user has no status.
     
    Advanced TTD Member 604 328
    R
    Richie is offline
    This user has no status.
     
    Advanced TTD Member 328 604

    User Info Menu

    #6
    Thanks all

    I tried a bit more earlier and gave up and just glued rubbers on anyway, there isn't much left on there but it's annoying. Never had anything like it. Even with extra glue layers on some weird glue is still left after taking it off. I also tried rubbing with left over rubber pieces but I need to scrub hard with my finger tips to get it off, it hardly even goes off, just moves to another spot on the blade. Maybe next time I'll try heating it. Can the heat really damage the wood?

  7. lodro is offline
    says TT-CLOWN, old git
     
    Senior TTD Member 281 796
    L
    lodro is offline
    says TT-CLOWN, old git
     
    Senior TTD Member 796 281
    #7
    Quote Originally Posted by Richie
    Thanks all

    I tried a bit more earlier and gave up and just glued rubbers on anyway, there isn't much left on there but it's annoying. Never had anything like it. Even with extra glue layers on some weird glue is still left after taking it off. I also tried rubbing with left over rubber pieces but I need to scrub hard with my finger tips to get it off, it hardly even goes off, just moves to another spot on the blade. Maybe next time I'll try heating it. Can the heat really damage the wood?

    Considering it was (or still is) a very thin layer of residual glue , you probably did the best that could be done by simply gluing a new rubber over the top of it. 😁

    Heating virtually any laminate , especially if done on one side only, is definitively a risk.

    In my early "gluing days" i used "glue-sheets" and they could be a complete pain in the arse to remove.
    Actually a rag with some mineral turpentine or white spirits carefully applied would remove any glue residue on the blade quite easily

    .
    BUT do not try it on the rubbers, unless you want a permanently """boosted""" sponge 😁😁😁


  8. brokenball is offline
    This user has no status.
     
    Elite TTD Member 468 1,006
    B
    brokenball is offline
    This user has no status.
     
    Elite TTD Member 1,006 468

    User Info Menu

    #8
    Quote Originally Posted by lodro

    WARNING ! Heating a blade with a hair dryer can lead to bending and warping . !!!!!!!

    Have you done it? I want to see a video of you warping a paddle or this is BS.
    If could only happen if you heat one side much more than the other and it would need to be MUCH more heat than what is required to make the rubber soft and tacky.
    Last edited by brokenball; 4 Weeks Ago at 02:55 AM.

  9. lodro is offline
    says TT-CLOWN, old git
     
    Senior TTD Member 281 796
    L
    lodro is offline
    says TT-CLOWN, old git
     
    Senior TTD Member 796 281
    #9
    Quote Originally Posted by brokenball
    Have you done it? I want to see a video of you warping a paddle or this is BS.
    If could only happen if you heat one side much more than the other and it would need to be MUCH more heat than what is required to make the rubber soft and tacky.

    have we got a misunderstanding here ?
    We are not talking about heating rubber but old hard glue that is difficult to remove.

    I suggest an experiment with some old crappy wooden blade. Hold a metal straight-edge on the blade surface to check if it is level (it is not likely that it is)
    then heat one side only and re-check.


  10. Gozo is offline
    says May the Spin be with you!
     
    Advanced TTD Member 250 392
    Gozo's Avatar
    Gozo is offline
    says May the Spin be with you!
     
    Advanced TTD Member 392 250
    #10
    Quote Originally Posted by Richie
    Does anyone know of a trick to remove tiny bits of residue glue from blades? I borrowed some glue a while ago that was really thin and it has been hell to remove. I've scrubbed for ages and got most of it out from the middle, but there is still like a very thin layer and residual glue everywhere, mostly on the edges.

    Is there some kind of solution I could pour on the blade that will remove the glue without damaging it?

    Thanks all.

    It's hard to see even in the picture.

    Me sad SOD previously. Then Me get to know Butterfly Free Chack II glue.

    Now me happy, residue easily removed just like those pencil eraser clump.

    One quick rub and it all drops off.

    More time to play TT.

    The Following 2 Users Like Gozo's Post:

    lodro and Richie


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Create a new Topic:
Title is required.