Back to Forum
Page 2 of 2 FirstFirst 12
Results 21 to 25 of 25
  1. mocker88 is offline
    This user has no status.
     
    Advanced TTD Member 78 215
    mocker88's Avatar
    mocker88 is offline
    This user has no status.
     
    Advanced TTD Member 215 78
    #21
    Quote Originally Posted by Niicky

    The rubbers don't shrink just like that, it's cuz you strecthed it when gluing. Notice how de sides haven't shrinked but only on the vertical. Only way is to boost and stretch a little when gluing it back on

    Well. The original 729 V-6 blade is a smaller one, but I'm always careful so I don't stretch new rubbers when putting them on. What I have experienced is that softer sponged rubbers tend to shrink more. I mean the first 3-5 times I move the rubbers, there's no problem. Usually when I put it in a plastic bag for storage some time, and then want to use it again, there has been some shrinkage going on. So I wonder if there's not any drying out process that make rubbers shrink a bit over time?

    The Following User Likes mocker88's Post:

    latej


  2. Kolev is online now
    This user has no status.
     
    Advanced TTD Member 82 239
    K
    Kolev is online now
    This user has no status.
     
    Advanced TTD Member 239 82
    #22
    My experience is that after expanding the rubber sooner or later it shrinks back. Someone in the previous posts mentioned already that the first time we cut the rubber have to wait till the glue is completely dry and try not to stretch. This may prevent extreme rubber shrinkage

  3. mocker88 is offline
    This user has no status.
     
    Advanced TTD Member 78 215
    mocker88's Avatar
    mocker88 is offline
    This user has no status.
     
    Advanced TTD Member 215 78
    #23
    Quote Originally Posted by Kolev
    My experience is that after expanding the rubber sooner or later it shrinks back. Someone in the previous posts mentioned already that the first time we cut the rubber have to wait till the glue is completely dry and try not to stretch. This may prevent extreme rubber shrinkage

    That's for sure, but I always wait for the glue to completely dry. Else it doesn't hold. And I haven't used booster before, so there's nothing that should expand the rubber then I think?


  4. Niicky is offline
    This user has no status.
     
    TTD Member 4 9
    Niicky's Avatar
    Niicky is offline
    This user has no status.
     
    TTD Member 9 4

    User Info Menu

    #24
    Quote Originally Posted by mocker88

    Well. The original 729 V-6 blade is a smaller one, but I'm always careful so I don't stretch new rubbers when putting them on. What I have experienced is that softer sponged rubbers tend to shrink more. I mean the first 3-5 times I move the rubbers, there's no problem. Usually when I put it in a plastic bag for storage some time, and then want to use it again, there has been some shrinkage going on. So I wonder if there's not any drying out process that make rubbers shrink a bit over time?

    softer rubbers are easier to stretch am I right😄 I've had thee same problem with FX-P but that was when I glued my first time. Now im really gentle when i roll on my rubbers

    The Following User Likes Niicky's Post:

    mocker88


  5. merlin el mago is offline
    This user has no status.
     
    Advanced TTD Member 62 417
    merlin el mago's Avatar
    merlin el mago is offline
    This user has no status.
     
    Advanced TTD Member 417 62
    #25
    My Dynaryz AGR also streched a lot.
    No more political prisoners in Catalonia.

Page 2 of 2 FirstFirst 12

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Create a new Topic:
Title is required.