Zyre 03 and Dignics 09c on FZD ALC

This user has no status.
My friend bought Sora's racket. I gave it a try today.

(I was initially planning to buy Dignics 09c on the both side of a FZD ALC. Huge fan of 09c and FZD ALC)

Now I'm in a dilemma should I get Dignics 09c or Zyre 03 on BH.

Pro D09C - My BH underspin is deadly with this, slow and low and very strong underspin. Much better than Zyre 03. Even for BH serving.

Con D09C - missing the punchiness of Zyre 03.

Zyre 03 sometimes produces unreturnable shots, even mistimed ones. Did anyone else feel that?

I don't understand the negativity about using pro rubbers. I'm definitely not a Pro but thoroughly enjoyed the racket.

What's your thought on Dignics 09c vs Zyre 03 on the BH?

I'll stick to dignics 09c on the FH.

One thing I noticed that Zyre 03 shots tend to land on the edge of the table.
 
  • Like
Reactions: blahness and Haito
says what [IMG]
says what [IMG]
🏆 Top 1% Commenter
Well-Known Member
Feb 2016
3,141
1,943
6,312
Read 2 reviews
Honestly, D09C missing the punchiness of Z03 is a negligible con. Because its good just as not as much as Z03 perhaps. Control is always more important to be honest, and Z03 is harder to use + backhand can make it worse.
If it's a con or not depends on the player, no? Someone might call it a desirable feature.
 
says what [IMG]
says what [IMG]
🏆 Top 1% Commenter
Well-Known Member
Feb 2016
3,141
1,943
6,312
Read 2 reviews
I just hope theres no skill issue as their equipment shows a beginner setup
I think there's things you can learn from using high-performance equipment even if it's "too much" for you that you won't learn from using low-performance equipment FWIW.

I think the only time buying stuff like this is just plain wrong is if you do it out of some kind of buying impulse or peer pressure. :)
 
I think there's things you can learn from using high-performance equipment even if it's "too much" for you that you won't learn from using low-performance equipment FWIW.

I think the only time buying stuff like this is just plain wrong is if you do it out of some kind of buying impulse or peer pressure. :)
Of course as long as you don't do it for hype either, or the willingness to be different because I know what its like when I was a stupid ameatur who went from all+ to szlc with two dignics rubbers. As long as it is within your control then of course, tacky imo is the best for learning, but most demanding.
 
says Making a beautiful shot is most important; winning is...
says Making a beautiful shot is most important; winning is...
🏆 Top 1% Commenter
Well-Known Member
Mar 2021
4,967
5,937
12,446
Until Zyre-09c comes out, of course.
serious discussion:

zyre09c if it is available will make no sense. zyre03 with its thick sponge hyper trampoline effect is meant for speed drive stylist.

09c is semi tacky which is spin focus drive. A super trampoline platform like zyre will negate the tacky effect of its top sheet as the ball will leave the top sheet before adequate rotation can be imparted unto it.
 
  • Like
Reactions: Coolsta Connor
says what [IMG]
says what [IMG]
🏆 Top 1% Commenter
Well-Known Member
Feb 2016
3,141
1,943
6,312
Read 2 reviews
serious discussion:

zyre09c if it is available will make no sense. zyre03 with its thick sponge hyper trampoline effect is meant for speed drive stylist.

09c is semi tacky which is spin focus drive. A super trampoline platform like zyre will negate the tacky effect of its top sheet as the ball will leave the top sheet before adequate rotation can be imparted unto it.
I have over a decade of experience with rubbers and elastomers and I wouldn't be so confident in saying what a design change would do, and less so why.

For one I've never bought that tackiness adds *any* meaningful performance in attacking strokes due to how much the mu benefit falls off at higher loads, and H3 switching from being a tacky rubber into being a mostly grippy rubber kind of confirms this.

I think the main reason to use adhesion in TT rubbers is to get better performance in serves and pushes by having higher friction and lower CR, without making the rubber wear out prematurely due to the compound being extremely soft, and without making the rubber extremely slow by lowering the sponge's elasticity. That's just a guess though.

I'm not sold on "dwell time" either; the spin is applied at the exact moment the ball leaves. It's just one motion. Granted if you adversely design the system then the compliance will be insufficient and the load transfer normal doesn't shift far enough offset from the ball's CG and you lose a lot of effective spin potential from the sponge elasticity, although that force will go into speed. I think the super thick sponge concept is mostly so that you can have the super speed while also having enough compliance that the load transfer normal shifts offset from the CG and you're not purely relying on transverse friction which is relatively low at high normal forces.

This too just a guess although based in some empiricism from other rubbers. :)
 
  • Like
Reactions: Coolsta Connor
Top