Search results

Tenergy or Rozena 1.7 are light and great for hitting or loop driving dead balls

It would be interesting to know how much a good LP chop blocker can vary the return spin from the same quality loops. I have a spare blade with LP that I use sometimes at the end of a practice session. I can play lazy man pips by just holding the blade out vertically and also chop down at...

Many TTD rubber reviews already have comparison tables at the end of the video like below. A more reasonable ask is if Dan and crew could roll up all the ratings into one master table and put it in a sticky in the equipment section. btw, the Spinsight videos are sponsored, so the TTD crew is...

Of course. Dan will not have the same swing speed on every swing. What is his variability swing to swing, one day versus another? For golfers using swing analyzers to dial in clubs, you have to have clubhead speed to do any meaningful comparisons. No clubhead speed = waste of time. High...

ZJK telling people to beware of scammers

Your website has pictures of the ITTF approved P40+ ball which is a seamed ball that I have bought lots of. The Gambler website currently only sells these P40+ balls and has the same description it has had for years: "Gambler has made the change to our own punch out manufacturing process; this...

Igor must have been doing some vodka boosting, didn't even bother to tape over the "AB ROLLER" writing in the picture

Fang Bo stated in one of his videos that LJK had the best consistent spin. FB has also talked about why he thinks ZJK, FZD, ML, etc. were better than him and some skills where he thought he was better.

First thing to try is new rubber on the killerspin premade if you can get the rubber off easily. It is a decent premade blade. If removal is too big of a hassle then good value wood blades are Yinhe U series or W6 for a little more money.

All scales have a margin of error. Read the documentation you got with your scale, it probably says the tolerance is +/- 1g or so for a cheap consumer grade scale like the one I have. If your first measurement was 56g, then it means the scale is telling you it weighs 55-57g. You make another...

TLDR Poor oversight of finances by the board of directors. Dainton bet big on Smashes, they lost a lot of money, especially in the USA. Dainton gets the boot. Other jobs will be consolidated. to save money. Some Smashes did very well, so they will keep doing those. Money losers will get...

"resign" in this case typically means the board told the CEO to quit or be fired

I have played on this table many times. It does not play like a nice ITTF wood table. It is playable and you will get used to it. 2 things I noticed that make it play better: 1- clean the table before playing, the bounce is much better when clean 2- seamless balls play better, like the XSF...

It would be interesting to see how the learning model works if you put LP on one side. How does an AI figure out which side to use and how long would it take?

Adaptation goes both ways. If Sabine played Dane for $$$, she would show pro level adaption. Dane is a very high level amateur, but has no chance to beat a top 10 player playing for real. For comparison, when Gao Jun was WR 30-40, she played in many open events against men and was rated about...

IgorGPT says - sponge porosity compliance can be verified with the oily booster detector followed by dry boosting with an ab roller

Read the durometer documentation. It will say that for the measurement to be valid, the sample thickness must be at least X mm. Typically at least 6mm for consumer grade meters you find online. A sample of at least the minimum thickness cannot have a rubber topsheet attached to it. No...

Glayzer is slightly slower with a bit more grip and spin than Rozena

@Dan Nice video, I have the same question maybe no mention of the anti brand because the video was sponsored by Andro? I have seen other sources say her anti is Dr N ABS, it this accurate? It would be interesting to know if Sabine also tried LP and if so, what was her reasoning for picking...

How can this work on domed or cut rubber?