Recent content by Giovanni Greco

  1. Giovanni Greco

    Italian fourth category, n.1989, shake attack, fh loops, bh block and flat attack.

    Italian fourth category, n.1989, shake attack, fh loops, bh block and flat attack.
  2. What table tennis rubbers & blade do you use?

    I am very sorry for that, but which hardness You used? I am using a fake SGH (metal grey package, mid hard), but original SGH may be 37, 38 or 39 on chinese hardness scale, that is stamped on sponge in a rectangle with the word HARDNESS and one of the three previous reported numbers. What about...
  3. What table tennis rubbers & blade do you use?

    Not so bad, i think enough for my level. But it's not the original one, but an AliExpress found copy that Sanwei support do not know. On the sponge of the copy I am using there is a stamp with a cinese ideogram followed by an H, traducing it means "Mid Hard", furthermore the sleeve of the...
  4. What table tennis rubbers & blade do you use?

    Changed setup: 729 Yellow ALC BH Dr. Neubauer Killer Extreme 2 mm FH Sanwei Gear Hyper mid hard 2,2 mm
  5. Maybe I don't need this many rubbers...

    Xiom Omega V Asia, 50d sponge and a very tender and also slightly sticky topsheet. See at 07:30...
  6. Sanwei Target National (Blue Sponge) vs. Sanwei Hyper Gear 39° for Forehand – Which One is Better?

    But Sanwei or also TenCorp site for EU customers have lower prices than Sanwei AliExpress store.
  7. Sanwei Target National (Blue Sponge) vs. Sanwei Hyper Gear 39° for Forehand – Which One is Better?

    Sanwei material can be purchased directly from Sanwei site (free shipping worldwide!!!), i bought my copy from AliExpress but i'm afraid is a fake (but good fake...), is semi tacky and enough fast, not low throw angle. After my purchase, i discovered Sanwei site...
  8. Spinlord Keiler 2

    I think You need something harder, like Bluefire M1/M1Turbo or Xiom Omega V Asia, softer rubber are too springy.
  9. why wait to dry the glue?

    Imo, if You spread well the glue and let it dry very long time (10 hours, for example), the glue become smooth and flat, and so the rubber glued; it's only needed to avoid grains on the glue layer. The rubber works fine when playing, and this is enough for me.
  10. why wait to dry the glue?

    I think it works if it's used only a few amount of glue. Furthermore i have some doubt about waiting only one hour to cut the first rubber, i think it should dry more hours, also 12 hours for the second rubber to be ready to be cut and played seems to be too little, because water evaporate much...
  11. Brand new, curled tensor rubbers?

    I bought some other Xiom rubbers, but no issues found, all planar rubbers, Xiom Vega Europe, Asia, X. Very higher quality than Elite, however, all harder rubbers but very easy to use, at this time Asia and X was best performing, Asia for speed and X for control.
  12. Xiom Vega series

    Yes, Asia has softer topsheet than X and Pro, and a bit bouncy than both X and Pro.
  13. Spinlord Keiler 2

    I found Keiler too much like a SP in 2mm sponge, but i liked it more on faster woods in 1.2mm. I think it's too spinny and sponge too soft, but i planned to retry it at the end of season. Much better Orkan II for disruption which i actually use, in the past i used Waran I 2mm, imo much better...
  14. Spinlord Waran II

    Hi, the productor says differently: https://spinlord-tt.de/products/waran-ii/ Furthermore i use Orkan II that has same sponge and has a clear built-in speed glue effect (https://spinlord-tt.de/products/preview-orkan-ii/): "The version named ORKan has a soft silver colored sponge (38-40 degrees...
  15. Medium Pips... for?

    Middle pimples are for rythm variations speed/slow, long/short and counter hitting hard with backhand. See this example:
Top