Search results

compared to MX-P the normal Aurus might be too slow. Consider Aurus Prime aswell

I just switched from G1 to D09c on my FH. G1 is bouncier and goes deeper than D09c. D09c is also so much better in the short game and pushing apartment. Only downside I have seen so far is G1 has a higher curve and is spinnier on slower loops, therefore my opponents tend to block out. Not sure...

No my blade is 90g aswell. G1 and r7 both 52g-50g =192? G1 and d09c = 197g Blade+ g1 was = 142g

what foil do you use for the rubber? Or did you just cut the one that comes with the rubber itself? I just played with the rubber today glued it 1h before training. Sadly only had trainingspartner who just wanted to warm up half an hour with normal drives and then did 2 matches against 2...

I just compared Rakza 7 with G1 on my long 5 blade. And for my backhand G1 felt softer why? According to this Thread my Rakza 7 should be softer. I am talking about the backhand loop (spinny) both rubbers were 2.0mm and I just flipped the racket. The feeling of the G1 was much better

Yesterday I beat him 3-1 (He plays in highest league in county). The one set I lost to was also down to 2 point difference. Actually that confused me a lot. I kept thinking I need more spin and so on. Turns out looping consistently with good placement where he is not already waiting to counter...

Well it will be too late by then. Because I dont have any protection foils. Never needed it for my previous rubbers. I will just use the one it comes with then instead of using none at all no? Also I tried G1 2,00mm on my BH. I just told my partner if he sees any difference. Basically brush...

Can I use the protective foil that comes with the rubber? Or was I supposed to buy an extra one? Also that weight would be really good for me almost the same as what I currently have. Is that 2,1mm or 1,9mm?

Alright Thanks for the Input! Will try to test it today even. Will flip rakza 7 with my g1 and see if I or my partner can see any difference

I already have g1. Just not sure if I should go max here from super thick. With Rakza on the other side my racket is around 188g. I doubt d09c is going to add another 12g. Hard to say if I will like that or not. My blade is already headheavy and I played better with 188g blade setup than...

First of all I ordered one "test" sheet of D09c red 2,1mm for the BH. I never really flipped my bat. Is that a thing? I thought there is a FH side and the Bh side and it plays "different" if I just flip. Or maybe it was with certain other blades idk. If its identical then I would try and give...

I am very unsure about chinese rubbers. I have no clue about boosting and such. I sometimes don´t even realize when the rubber loses its effect because I can adjust to the setup really well. And from what Timo B. said with D09c I don´t have to worry about that like H3 rubbers. But for now I am...

In what way would I need to adjust to D09c. 3-4 years ago I tried a used Tenergy 05 and the faster I did my backhand topspin the more "secure" it felt. In terms of I knew its gonna land on the table which I didn´t experience with any other rubber since then. But because I couldn´t tell how used...

Hello everyone, I currently play Rakza 7 2.0mm on my BH. My FH is a G1 2.0mm. My racket is ~200$ Long 5 90g I like to play with a lot of spin and 3rd Ball attack. I mostly block, flick their service (only backhand side), or loop. I dont really counterloop on the bh side. Are any of those listed...

Talk with him and find out how he feels during the game and train him mentally aswell. Film him and check what kind of mistakes he makes. Hard to analyse it from the outside.

How can I properly borrow the energy from my opp ball? I might be hitting the ball at the backside and move up to give spin to the ball which makes it go out. But if I do it with a closed angle it's very inconsistent and I hit the edge of the racket or contact the ball too thinly. When I hit...

I got really good against backspin balls (FH TS) but against block or even worst if they have slight topspin even my shots go out. 50% far and 50% slightly over the table. I feel like I dont hit the ball at the same Distance towards my body as those half long backspin balls that I can hit right...

@jk1980 Currently I am hitting the ball more over the table than into the net. I also wanna go max Sponge thickness. But that would make my balls go more out no? I was thinking about switching to a rubber where I can go max thickness but that has a lower throw angle than my G1 on my FH. My...

@jk1980 Thats a very good video from XOLAY. It made a click combined with the video I posted earlier. This one showing a better angle. I have seen huge progress in my shots. I loop with a more open racket now and go all in and understand much better how I need to position myself towards the...

"Racket angle more closed, Hitting the ball more on its the upper side, Squeeze my hand tight right before hitting the ball to not release too much power." Thats what I have been doing (blue screenshot of @jk1980) . My plan is use my hip rotation and just experiment with the stroke till I find...