Testing H3 with TTEX speedlim (speed glue) and how to use speed glue?

[Ahma]

Hi, I just ordered a sheet of Hurricane 3 Neo and some speed glue which was called TTEX speedlim. I was wondering how many layers of glue should I put? I’ve never tried the rubber or the glue.

 

[Lula]

You use speed glue before every play.

 

[mocker88]

Isn't H3 NEO pre glued with water based glue? I haven't tried it with speed glue, but I think that I read it somewhere. Perhaps if you remove the glue layer before speed gluing then?

 

[Ahma]

If it had already glue, might as well just put 2 more layers instead of 3 and 1 or 2 layers on the blade.

 

[Ahma]

I found this site: https://gregsttpages.com/archives/g...o use several,have found out from experience!

it says to prime the rubber first, so I guess the rubber has already been primed due to it having a normal glue layer, but we’ll see.

 

[Tommy16]

If there is some kind of layer on the sponge you should first remove it. Then put one layer to the blade and one to the rubber. Let them dry. Then put another layer to the blade and let it dry. When glue layers on the blade are dry then put one more layer to the rubber and put the rubber to the blade right away. After an hour - hour and a half you are good to go. Remember that speedglue effect has a short peak which last`s only few hours.

Cheers,
Tommi

 

[Tony's Table Tennis]

Is this what you have?
https://en.ttex.se/ttex-uberbooster-120ml.html

 

[Ahma]

Like I said, it has to be “primed” so I don’t think I’ll remove the layer. But yes I know how to glue. And no that’s not the glue, it was called speedlim.

 

[Tony's Table Tennis]

Like I said, it has to be “primed” so I don’t think I’ll remove the layer. But yes I know how to glue. And no that’s not the glue, it was called speedlim.

I can't seem to find speedlim on the internet
anyways, a couple of chinese brands who make boosters, also make speed glue.

For those brands, all you need to do is, glue the rubber like a normal glue.
it will say something like 4 to 6 layers as per your preference, glue when dry. and last layer let it dry for about 70 to 90 mins before putting it on.
So if speedlim is anything like those Chinese speed glues, I would assume it is similar.

For cost saving, people tend to use cheaper / normal glue on the blade (1 or 2 layer of normal glue is sufficient)
The lasting time for these speed glue as per the chinese company is around 24 hours.

 

[Ahma]

Thanks, i guess its like those chinese ones. Here’s the link for the glue https://www.ttex.fi/ttex-speedlim-250ml.html

 

[Ahma]

Or maybe it’s just voc water based glue if that’s a thing, just ordered it by it’s name because it’s Swedish for speed glue. And I’ve seen speed glue it these types of “cans”. But most likely speed glue or something close to that.

 

[Tony's Table Tennis]

Or maybe it’s just voc water based glue if that’s a thing, just ordered it by it’s name because it’s Swedish for speed glue. And I’ve seen speed glue it these types of “cans”. But most likely speed glue or something close to that.

is the glue like very thick and see through? maybe send me some pics

 

[Ahma]

Oh you didn’t read the first message, I ordered it yesterday. It’ll arrive next week.

 

[lodro]

https://www.ttex.se/ttex-speedlim-250ml.html

The good old illegal speedglue..............

BRILLIANT !!!!!!!!!

 

[Ahma]

So it is speed glue, good to know. Thanks.

 

[lodro]

I reckon you might have been better off just buying standard H3 not Neo.
They say : Neo has been factory boosted
They say : the boosted rubber has then been crudely covered with some waterbased glue that looks like hog-snot.

I would remove the layer of glue.

 

[Ahma]

Alright I’ll remove it. That store didn’t have the regular h3.

 

[lodro]

Alright I’ll remove it. That store didn’t have the regular h3.

that is actually quite a fair price, kr 239
why don't you keep the neo for later and order a plain commercial H3 from aliexpress ?

 

[Ahma]

Cuz I’m at my dads till 24th and after that I have confirmation school. So i dont got time sorry.

 

[Ahma]

But I’ll remove the layer don’t worry