Best Chinese sticky rubbers that don't need boosting

says what [IMG]
says what [IMG]
🏆 Top 1% Commenter
Well-Known Member
Feb 2016
3,111
1,920
6,285
Read 2 reviews
Yes, FP is falco platinum. The massage gun is the cheapest one with cushioning ball attachment. I use a sheet of 729 super to cover the surface of the new rubber. I put the stack between 2 sheets of cooking paper and pressed with the massage gun most of the surface, from the sponge side. Sometimes I measure 1-2 degrees softening of the sponge, but most of the change is in the reducing of sponge damping, or energy loss during rebound.
Have you measured the hysteresis or is this just some impression? I can't really say I've ever used *any* rubber that didn't just become slower and less bouncy after use.
 
This user has no status.
This user has no status.
Member
Jun 2025
324
335
964
Read 1 reviews
Have you measured the hysteresis or is this just some impression? I can't really say I've ever used *any* rubber that didn't just become slower and less bouncy after use.
I am using durometer on multiple points, from the sponge side. Bounsing test is subjective. After treatment the rubber is more consistent across the surface. My impressions are mostly on slow, middle to hard rubbers.
 
says what [IMG]
says what [IMG]
🏆 Top 1% Commenter
Well-Known Member
Feb 2016
3,111
1,920
6,285
Read 2 reviews
I am using durometer on multiple points, from the sponge side. Bounsing test is subjective. After treatment the rubber is more consistent across the surface. My impressions are mostly on slow, middle to hard rubbers.
You should just measure the bounce height when dropped at low speed. The CR is highest at low speed, around 0.5 to 0.7, and the deltas will be the highest if there is any. I've only ever found lower CR which is consistent with breakdown of the sponge.
 
This user has no status.
This user has no status.
Active Member
May 2023
659
960
2,155
Cuifeng more heavy and hard and Chinese blue sponge like. Durability is very good. It's not that bouncy but not slow it's hard and quite fast. Needs good power to be hit through but if you manage to it's so good and rewarding.
what do you think of pinyi cuifeng blue sponge 37-38 degree version?

I always preferred h3 bs 39 because its easier to hit through, there was even a time where I used boosted h3 37 os on fh and liked it

wondering which version (37-38 or 39-40) fits me better since u said pinyi cuifeng is quite hard
 
This user has no status.
This user has no status.
🏆 Top 1% Commenter
Well-Known Member
Mar 2013
1,045
1,483
3,187
Read 3 reviews
Just a quick note on the Tuttle 25 and 27 rubbers mentioned previously on the thread. I was interested in their take on Zyre-style sponge thicknesses so I ordered sheets of 25 in red and 27 in black. However, what arrived was....interesting:


sponges.jpg


I mean, I've been alive for more than 5 minutes so I know not to expect perfection from Chinese rubbers in general. But as you can see, 25 is really thick, bigger than the Zyre and the entire rubber is very, very close to the 4mm limit overall. But then the 27, which should be thicker than the 25, is nowhere near that and is slightly thinner than the G20, which should be 2.2mm. These are straight out of the packet, no boosting by me.

When you buy rubbers specifically for the uber-thick sponge, it's a shame to get this but not a surprise of course. The red 25 is labelled as 2.5mm 45 degree, the black 27 is labelled 2.7mm 39-40 degree. Not used either yet. I won't waste your time with "buyer beware".
 
This user has no status.
This user has no status.
🏆 Top 1% Commenter
Well-Known Member
Oct 2018
1,742
2,159
4,399
what do you think of pinyi cuifeng blue sponge 37-38 degree version?

I always preferred h3 bs 39 because its easier to hit through, there was even a time where I used boosted h3 37 os on fh and liked it

wondering which version (37-38 or 39-40) fits me better since u said pinyi cuifeng is quite hard
I wouldn't go down to 37-38, unless for BH. FH I think it would feel too bouncy with not enough support for hard hits.
 
says what [IMG]
says what [IMG]
🏆 Top 1% Commenter
Well-Known Member
Feb 2016
3,111
1,920
6,285
Read 2 reviews
Loki arthur china without boosting is pretty decent for backhand if you are not seeking really high speed hybrid
My impression from using it for a few sessions is that it's pretty mediocre for a forehand rubber, but I thought it'd be pretty good for the backhand. Funnily that was also my impression of Jupiter 3 38A and they measure almost exactly the same hardnesses in Shore A and O on both sides of the sheet.
 
I am not sure if Gambler X3 diamond gold label made the list, but it should be here as well.
So I've been using the H3N Commercial 38 boosted on my FZD ALC and replica W968. The sponge dies too quick with 2 layers of booster. I find there's also an issue with the consistency of the the topsheet on the H3N Commercial. They don't retain the tackiness like they use to. I had a sheet of Gambler X3 Diamond Gold Label on my Xiom Hayabusa ZXi for BH. I believe I had it boosted with Haifu Sea Moon two layers. I was able to get nice cracking counter topspin. I tried it briefly for FH and surprisingly liked it better than the 729 Battle 2 National Blue Sponge 38 boosted that was actually being used for the FH. I ended up taking a fresh X3D GL off another blade and put it on my FZD ALC. Unboosted it did not perform the way I liked it but I could feel that it can give more when the sponge is really engaged. I took it off and boosted with two layers of Haifu Sea Moon and it has been playing really good so far. The tackiness is so much better. Spin generation on serves is about the same as the H3N. Topspin loops and drives seem to drop closer to the net. Topspin counters and drives stay low to the net with secure feeling. I'm going to continue playing with it for a while and see how it goes.
 
This user has no status.
This user has no status.
Active Member
Jun 2026
639
456
1,788
Just a quick note on the Tuttle 25 and 27 rubbers mentioned previously on the thread. I was interested in their take on Zyre-style sponge thicknesses so I ordered sheets of 25 in red and 27 in black. However, what arrived was....interesting:


View attachment 43047

I mean, I've been alive for more than 5 minutes so I know not to expect perfection from Chinese rubbers in general. But as you can see, 25 is really thick, bigger than the Zyre and the entire rubber is very, very close to the 4mm limit overall. But then the 27, which should be thicker than the 25, is nowhere near that and is slightly thinner than the G20, which should be 2.2mm. These are straight out of the packet, no boosting by me.

When you buy rubbers specifically for the uber-thick sponge, it's a shame to get this but not a surprise of course. The red 25 is labelled as 2.5mm 45 degree, the black 27 is labelled 2.7mm 39-40 degree. Not used either yet. I won't waste your time with "buyer beware".
That’s some delicious looking liquorice allsorts
 
This user has no status.
This user has no status.
🏆 Top 1% Commenter
Well-Known Member
Oct 2018
1,742
2,159
4,399
I gave one one of my Chinese friends a sheet of Sanwei Target national 3, the normal version. He normally used H3 BS on FH and H3 OS on BH and since he is lacking some raw impact power I said to him to try the STN since it's easier to hit trough and has more speed. And so he tried it first on FH and he liked it a lot and his shots were much more fast. Before I could be very calm against him but now I need to be on the edge. So now he bought 2 sheets, both FH and BH and will probably use it on his FZD SZLC, but I think it was really good on his Viscaria already. I used STN with Mizutani ZLC and it was pretty good so maybe FZD SZLC will also be good.
 
This user has no status.
This user has no status.
Member
Nov 2025
14
3
17
I gave one one of my Chinese friends a sheet of Sanwei Target national 3, the normal version. He normally used H3 BS on FH and H3 OS on BH and since he is lacking some raw impact power I said to him to try the STN since it's easier to hit trough and has more speed. And so he tried it first on FH and he liked it a lot and his shots were much more fast. Before I could be very calm against him but now I need to be on the edge. So now he bought 2 sheets, both FH and BH and will probably use it on his FZD SZLC, but I think it was really good on his Viscaria already. I used STN with Mizutani ZLC and it was pretty good so maybe FZD SZLC will also be good.
Could you send a pic of which packaging STN3 you're talking about? The silver package or purple-ish? There are a lot of variants out there so it's quite confusing.
 
This user has no status.
This user has no status.
Member
Mar 2024
120
147
305
-1, Pinyi Cuifeng, it has the most potential on normal production blades. It has the speed the hardness the topsheet grip and stick and snap, I think it is probably the most safe rubber. If you use it on a very hard blade it will be difficult to use but the potential is there. Weight is better than german rubbers and durability is excellent.
Do you know what versions of cuifeng you got? I talked to Gan recently and he told me that there are 2 versions. One that needs boosting and one that doesn't.

Apparently the version 3.0 is no-boost version and the 3.5 (or any 0.5 versions he says) still needs a bit of booster.

I'm ordering a few, since we have visitors from china. Intent to use it for off-season and training :D
 
This user has no status.
This user has no status.
Member
Jun 2025
324
335
964
Read 1 reviews
12666.jpg


KTS Master G52, red, 2.1mm. 67 grams for square 165×165mm with foil. The sponge is dense and is real 52 degrees shore O, a real 2.1mm sponge. The level of stickiness is low and brushing friction doesn't feel on H3 level. The topsheet feels soft but is very thick, more than XVC and VS>401, similar to the red 729 BB. Cylindrical pips with H3 density and vertical orientation. There is no hint of tenzor effect and factory boosting. Smells good, better than 729 rubbers. I don't know when will test it due to other priorities. Will update the post or add comment when I do it.
 
This user has no status.
This user has no status.
🏆 Top 1% Commenter
Well-Known Member
Oct 2018
1,742
2,159
4,399
I've been trying out Tuttle 27 with the 2.7mm sponge. I didn't measure but it's thicccccc so I just say it's 2.7mm.

Its a fairly interesting rubber. It had a small dome out of the pack so maybe it's a bit boosted or could be how the sponge and topsheet are glued together, I'm not sure.
The pips are very short and the topsheet is sticky, I won't say it's super sticky but mine is sticker than a H3. And it grabs the ball quite well, it doesn't slip the ball at more closed angles, how Hurricane does it for me.
I only played like 3 hours with it and first it didn't feel bouncy or that fast or particularly spinny, but I feel like the sponge is breaking in and it's getting faster a bit.
It's quite easy to control it, not spin sensitive at all.
First it didn't feel spinny at all but now I am confused since if a do slow open up loops people tend to block it long, so even tho I don't feel how much spin is created it does seem to produce a lot for openup loops.
On 3rd ball fast attacks it's also quite good, I was worried since first I didn't feel the blade being there under the sponge but as it's breaking in I feel it more and more and it seems to be quite good at this aspect too.

I did do some really crazy shots with it which surprised me, like I say it feels different than rubbers I used before and I don't feel how it generates the spin and how much I don't actually know if these crazy shots were due to it being not sensitive or being super good and grip and spin generation.

I don't know if I like it more than LAC, it shows some positive aspects, but I also feel the LAC topsheet grips the ball even more.

Loki rubbers have the best grip for me, even at the most extreme angles they grab the ball securely... LAC and Rxton 7, Rxton 9 too.

So I'm a bit baffled to keep trying the Tuttle 27 or stick with LAC or try a softer R9, since the 40.5 felt too hard for me and slow but the spin was huge...

So confused hhhhhh


Ps: I just measured its weight, mine is 56g cut. Well that also give some explanation why it feels good to use, but it messes with my backhand.
 
Last edited:
Top