This user has no status.
How does this compare to the Omega 7 china Guang?
If you can brush properly, i think the 40 degree version is spinnier.
Its 39 sorry. I was thinking of another rubber. I keep mixing this up.40 deg version available ? Dealer has 37/38/39
Hi,
I play the 39°-Version FH and BH on a Septear Feel Inner which should be not too far away from the Lead? It is a really good combination, too. For a test I have tried the Victas ZX Gear Fiber, which felt too slow - or better said boring with the Gear Hyper - very good control, but no pressure at all.
I believe that the combination of the Gear Hyper with a blade which has a little (or more) catapult is a good idea.
All the best
40 deg version available ? Dealer has 37/38/39
Hi BVGN.....I'm Interested to know more about your experience with Nitt. Septear Feel Inner - curious to know about the "feel" of this blade, also speed rating (approx), spin generation etc. Wonder how it compares with Nitt. Acoustic or Acoustic Carbon Inner?. Not much info on it around. I also just started using Sanwei Gear Hyper 39 and think it a superb rubber imo. Cheers....
The AGR and ACC are both faster by a good margin. Although the Gear Hyper is already fast, it is somewhat in the level of Acuda S2.yogi, how does the 39 version compare to the Joola AGR and ACC?
Thanks, so it's fair to say the Gear Hyper is relatively slow by today's standards of "very fast" rubbers.The AGR and ACC are both faster by a good margin. Although the Gear Hyper is already fast, it is somewhat in the level of Acuda S2.
yogi, how does the 39 version compare to the Joola AGR and ACC?
Thanks, so it's fair to say the Gear Hyper is relatively slow by today's standards of "very fast" rubbers.
The 38 degree version of Gear is what you would like but it is less spinny that Rakza Z.I am looking for a replacement rubber on backhand of my Darker 7p-2A.7t (7ply Hinoki). Due to the blade's characteristics (high throw + strong catapult) in combination with Rakza Z / 2.0 mm on my BH (high throw) blocks and flicks tend to fly off the table too often.
Could the Gear Hyper be a good replacement since it seems to have a medium-low arc? What I really liked about Rakza Z is the strong grip due to its semi-tacky top sheet. From what I read the Gear Hyper has quite a grippy top-sheet and still offers good amount of speed.
Ideally my new backhand rubber would be slightly slower and has a lower trajectory than Rakza Z, but still has the same linear playing characteristics. Could the Sanwei Gear be the solution?
I am also still thinking whether I should get the 38 or 37 degree version. Rakza Z to me felt like 50 degree ESN scale hardness which I liked for BH...could be a tad softer maybe T05-like.
I am looking for a replacement rubber on backhand of my Darker 7p-2A.7t (7ply Hinoki). Due to the blade's characteristics (high throw + strong catapult) in combination with Rakza Z / 2.0 mm on my BH (high throw) blocks and flicks tend to fly off the table too often.
Could the Gear Hyper be a good replacement since it seems to have a medium-low arc? What I really liked about Rakza Z is the strong grip due to its semi-tacky top sheet. From what I read the Gear Hyper has quite a grippy top-sheet and still offers good amount of speed.
Ideally my new backhand rubber would be slightly slower and has a lower trajectory than Rakza Z, but still has the same linear playing characteristics. Could the Sanwei Gear be the solution?
I am also still thinking whether I should get the 38 or 37 degree version. Rakza Z to me felt like 50 degree ESN scale hardness which I liked for BH...could be a tad softer maybe T05-like.
I think H3Neo H37 is optimal, but I guess you already tried...
You could try Rising Dragon, it's softer and a bit slower than RZ, also semi-tacky. I only had couple of hits with it, but that is how it felt. Has good spin, not sure it will solve the problem with blocks though.
Haven’t tried H3neo 37 yet, but wouldn’t be the throw even higher than with a harder version of H3neo (using 40 degree OS in FH at the moment)
Haven’t tried H3neo 37 yet, but wouldn’t be the throw even higher than with a harder version of H3neo (using 40 degree OS in FH at the moment)
When I compare H3Neo H41 vs H37, I don't see much difference in throw angle. The H41 is a bit faster, harder obviously, so on BH with H37 is easier to grab the ball, more so on flicks. If the H40 suits you on FH on that blade, chance is, the H37 will on BH too.
When I compare H3Neo H37 vs RZ, the H37 is slower, even more linear. Hardness is for me hard to compare due to different feeling of sponges. I learned I prefer the "non-porous" sponge, followed by micro-porous sponge like on Bluegrip C1/C2, followed by the sponge like on RZ (which I still quite liked, but on BH only).
For me the H3 37 has a more ridiculous arc than h3 41. This could be good and bad at the same time depending on the player.
The 38 degree version of Gear is what you would like but it is less spinny that Rakza Z.
Did you try boosting the Gear Hyper? I am still thinking whether to get the 38 degree version and boost it to get it a touch softer and a bit more lively or otherwise going for the 37 degree version (which is closer to T-05; 36 DHS butterfly scale) without boosting.
Is there a significant difference in playing characteristic between 38 and 37 degree that you could observe?
What would be the approximate cut weight for each on a 157x150mm blade head?
i only tried boosting it 1 layer when new and then 3 more layers after 30 days. It felt i was using a Tibhar Sinus rubber.Did you try boosting the Gear Hyper? I am still thinking whether to get the 38 degree version and boost it to get it a touch softer and a bit more lively or otherwise going for the 37 degree version (which is closer to T-05; 36 DHS butterfly scale) without boosting.
Is there a significant difference in playing characteristic between 38 and 37 degree that you could observe?
What would be the approximate cut weight for each on a 157x150mm blade head?